cavity wall

英 [ˌkævəti ˈwɔːl]

美 [ˌkævəti ˈwɔːl]

n.  (有保暖作用的)空心墙，夹壁墙

医学

牛津词典

noun

• （有保暖作用的）空心墙，夹壁墙
  a wall consisting of two walls with a space between them, designed to prevent heat from escaping
  1. cavity wall insulation
     空心墙隔热

柯林斯词典

• N-COUNT (隔音或防寒的)空心墙，夹层墙
  Acavity wallis a wall that consists of two separate walls with a space between them. Cavity walls help to keep out noise and cold.
  1. ...cavity wall insulation.
     空心墙隔音材料

英英释义

noun

• a wall formed of two thicknesses of masonry with a space between them

双语例句

• Aiming at the injection mold structures of female mold on stationary mold, the force on the famale mold and male mold are analysed, and the cavity wall thickness are calculated.
  针对凹模安装在定模上、凸模安装在动模上的注塑模结构，对矩形型腔模具进行了受力分析和型腔壁厚计算。
• Cavity wall masonry structure is a kind of special structure, because of its simple construction, low cost, so long in many of our relatively low level of economic development are widely used in many areas.
  空斗墙砌体结构作为一种比较特殊的结构形式，由于其施工简便、造价低廉，因而长久以来在我国许多经济发展水平相对较低的地区得到广泛的采用。
• Depending on the test results, the paper proposed a shear strength empirical formula which is suitable for high-performance ferrocement reinforcement rowlock cavity wall. This empirical formula is reference use to reinforcement design in the actual project.
  同时根据试验结果，提出了适合高性能复合砂浆钢筋网条带加固空斗墙砌体结构抗剪承载力的建议经验公式，可供加固设计人员在实际工程中参考使用。
• During the shore period of observation, carcinoma node, dimension of the cavity, thickness of the cavity wall and volume of liquid in the cavity have dynamic changes.
  囊腔内壁有附壁“结节影”（癌结），腔内有液体，在短期观察中“癌结”、“囊腔大小”、“囊壁的厚度”和“腔内液量”均有动态变化。
• The Strength of Sand Mold for Vacuum Evaporation Pattern Casting ( VEPC) and the Moving of Cavity Wall
  负压实型铸造砂型强度及型壁移动的影响因素
• The three main problems faced by water pump are leakage, vibration noise and corrosion of the impeller and water cavity wall.
  汽车水泵的三个主要故障是泄漏、振动噪声和叶轮或水腔内的腐蚀。
• This numerical simulation on gas penetration, pressure field, displacement process of melt-gas boundary in different time, and skin melt forming on the cavity wall is developed for GAIM parts.
  该研究对气体的穿透过程、压力场分布、小同时刻熔体/气体边界的移动状态以及在模壁上形成表层聚合物熔体壁厚的过程进行了气体辅助注射成形充模流动的实例数值模拟研究。
• According to theories and experiments, this paper test condensation phenomenon of cavity wall.
  理论和试验相结合对夹芯墙体的冷凝现象进行了检验。
• According to the wall testing process, we put finite element numerical simulation on the cavity wall which is set the ring beam but without structural concrete column, using discrete model to analysis the principal stress, cracks distribution and displacement of the wall.
  参照墙体试验过程，对设置圈梁但无混凝土构造柱的空斗墙体进行有限元数值模拟，采用分离式模型对墙体的主应力、裂缝分布与墙顶位移变化进行分析。
• Restoring force of small concrete hollow block cavity wall
  混凝土小型空心砌块空腔墙体的恢复力试验研究